An Integrated Publishing, Inc. Site

An Integrated Publishing Website

MS27308 Connector, Battery Cell, Offset

Pages 1 - 2 - 3

MS27308C

Ltr	Dash no.	Inches		Millimeters		Ltr	Dash no.	Inches		Millimeters
		Min	Max	Min	Max			Min	Max	Min	Max
A	-1	2.115	2.135	53.72	54.23	N	All	.177	.197	4.50	5.00
	-2	2.780	2.800	70.61	71.12
B	-1	1.615	1.635	41.02	41.53	P	All	.365	.385	9.27	9.78
	-2	2.030	2.050	51.56	52.07
C	-1	.240	.260	6.10	6.60	R	All	.719	.781	18.26	19.84
	-2	.365	.385	9.27	9.78
D	-1	1.070	1.090	27.18	27.69	S	All	.800	.840	20.32	21.34
	-2	1.380	1.400	35.05	35.56
E	-1	.468	.488	11.89	12.40	T	All	.609	.629	15.47	15.98
	-2	.560	.580	14.22	14.73
F	-1	.302	.322	7.67	8.18	U	All	.984	1.004	24.99	25.50
	-2	.365	.385	9.27	9.78
G	-1	.469	.531	11.91	13.49	v	All	.609	.629	15.47	15.98
	-2	.719	.781	18.26	19.84
H	-1	1.689	1.719	42.90	43.66	w	All	.502	.512	12.75	13.00
	-2	2.125	2.155	53.98	54.74
J	-1	.173	.183	4.39	4.65	x	All	.365	.385	9.27	9.78
	-2	.213	.223	5.41	5.66
K	-1	.115	.135	2.92	3.43	y	All	.750	.810	19.05	20.57
	-2	.240	.260	6.10	6.60
L	-1	.240	.260	6.10	6.60	z	All	.375	.405	9.53	10.29
	-2	.365	.385	9.27	9.78
M	-1	.052	.072	1.32	1.83
	-2	.115	.135	2.92	3.43

FIGURE 1. Interface and physical dimensions - Continued.

NOTES:

1. All dimensions are in inches.

2. Unless otherwise specified, tolerances are ±.010 for inches and ±5° for angles.

3. Metric equivalents are given for general information only.

4. Remove all burrs and sharp edges.

5. Steel stamp Part or Identifying Number (PIN): .005 inch (0.13 mm) deep minimum using .125 inch (3.18 mm)

high characters before plating.

REQUIREMENTS:

Material: Copper in accordance with ASTM-B187/B187M or ASTM B272 . Finish: Nickel plate in accordance with SAE-AMS-QQ-N-290 , type v.

2

For Parts Inquires submit RFQ to Parts Hangar, Inc.
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business

© Copyright 2015 Integrated Publishing, Inc. Site Design & Marketing by Strategico.